1, large-capacity, strong environmental protection. The zero-vehicle self-loading and unloading garbage truck product adopts a fully-sealed structure. The seal assembly adopts a high-quality material with a long service life, and the vehicle is shipped with garbage that has been subjected to compression treatment work. Under the same volume, the load quality increases, and There was no overflow of sewage, no roads were polluted, and secondary pollution was completely eliminated in zero operations. Low operating noise. Urban self-loading and unloading garbage truck products shall be optimized through the hydraulic system and loading mechanism, reducing the machining accuracy and assembly quality so as to reduce the noise caused by vehicle operation. 2, zero car shape beautiful, easy to clean and self-cleaning. The design of compartments for self-loading and unloading garbage trucks in the city adopts a framework structure with a door frame, which is more economical than the box-type framework structure of the conservative dump truck, and has a visually beautiful flow lag. Since there is no horizontally oriented skeleton in the cabin, there is no easy-to-save and dirt-retaining material; especially the top This avoids the rainwater row in the box of the same type from going out, and it is not enough to cause corrosion acceleration at the top of the compartment. The middle surface material of this product adopts phosphating and other surface treatment processes. The paint has strong adhesion, the surface is corrosion-resistant and smooth, and it is convenient for zero-vehicle cleaning. Its self-cleaning performance is much better than similar models. 3, dump system uses a combination of cylinder and rod system design, advanced performance. The combined dumping mechanism of oil cylinder and rod system has the advantages of good sealing performance, no leakage of hydraulic oil, long working life, reliable performance and good stability. In particular, because the product is unsatisfactory in the dumping site, because the fuel tank does not highlight the lower part of the chassis of the vehicle, its performance is better than that of a direct-pushing cylinder. 4, the back door institutions design advanced. The rear door opening mechanism can refer to the advanced European model design. The structure is compact and reasonable. It takes up a large size of the width of the carriage, allowing more space for the width of the carriage, making the width of the carriage larger, and making the car driver more comfortable. The docking of various types of garbage compression stations will help reduce work efficiency and avoid accidents in the carriage collisions between vehicles and stations. 5, lightweight design of the car body, load quality. The material of the dump trucks in the city can be replaced with manganese steel instead of the conservative carbon steel, and its weight is more than 20% lighter than that of similar cars. Therefore, the product design is conducive to energy-saving emission reduction, and for the user to reduce fuel consumption and reduce the cost of product use. 6, advanced and reliable hydraulic operating system. Urban self-loading garbage trucks are characterized by large size, long life, reliable performance, and easy operation. 7. Closed compression garbage trucks in the city's self-installed garbage trucks are rubbish transport vehicles used in conjunction with compressed garbage stations. When the trucks are docked with the station's compression box, the hydraulic system is installed in the middle of the carriage. At the end, the mechanism that connects the back door to the back door first opens the back door and closes the back door. After docking with the station, the hydraulic device at the compression station pushes on the garbage that has been compressed by the work and enters the garbage compartment. The garbage truck then closes the back door and leaves the garbage. When the garbage truck leaves, the rear door self-secures, and the body is lifted by a lifting mechanism consisting of a cylinder, a triangle plate, and a pull arm on the sub-frame, so that the trunk rotates around the rear-end reversal axis by 55 degrees and rubbishes the garbage. Pour out of the car. The car then landed in place and the back door closed silently. This shows that the product has the advantages of convenient loading and unloading of garbage, high level of self-repose, and high work efficiency. Monitoring device and data transmission device. In the cab, there is a video surveillance device for the operation supervisor to monitor the loading and unloading operation status of the garbage, and a noise self-checking recorder, data storage and on-line transmission device are installed. Xigong Chusheng (Hubei) Special Purpose Vehicle Manufacturing Co., Ltd. Precision CNC Slow-wire Cutting Processing
Precision CNC Slow-wire Cutting Processing is a specific manufacturing process that utilizes Computer Numerical Control (CNC) technology to cut intricate shapes and designs out of various materials using a slow-wire cutting method.
The slow-wire cutting process involves using a thin wire, usually made of tungsten or brass, that is heated and guided by a CNC machine to precisely cut through the workpiece. The wire is slowly fed through the material, allowing for intricate and precise cuts to be made.
This process is commonly used in industries such as aerospace, automotive, and electronics, where intricate and precise components need to be manufactured. The slow-wire cutting process offers a high level of accuracy and repeatability, making it ideal for producing complex parts with tight tolerances.
Some advantages of precision CNC slow-wire cutting processing include:
Accuracy: The CNC-guided wire ensures precise and consistent cuts, resulting in highly accurate components.
Versatility: This process can be used on a wide range of materials, including metals, plastics, and composites.
Complex shapes: The slow-wire cutting method allows for the production of intricate and complex shapes that would be difficult or impossible to achieve with traditional cutting methods.
Minimal material waste: The thin wire used in the process minimizes material waste, making it a cost-effective manufacturing method.
High surface quality: Slow-wire cutting produces smooth and burr-free edges, reducing the need for additional finishing operations.
Overall, precision CNC slow-wire cutting processing offers a reliable and efficient method for manufacturing intricate and precise components. Its accuracy, versatility, and ability to produce complex shapes make it a valuable process for various industries.
Precision Cnc Slow-Wire Cutting Processing,Alloy Slow Wire Processing,Nc Slow Wire Machining,Cnc Slow Wire Processing DONGGUAN YUSHUN PRECISION MOULD CO.LTD , https://www.yushunmolds.com