At present, the domestic used car market is quite confusing, and many consumers are afraid to buy an accident car. In the end, how do you identify whether the car is an accident car ? In fact, there are many ways. The following are some of the experiences that Xiaobian has shared with you. First look at the front face, observe the details, and whether the two sides are symmetrical; whether the headlights and the fog lights on both sides are the same or not; whether the gaps on both sides of the hood are the same. Then take a look around the vehicle and look at the side, look at the waistline, and then look at the color difference between the various plates, look at the gap, see the sheet metal repair, sheet metal repair will have some uneven place, made the paint , The paint is irregular underneath. Note that it is irregular. Looking at the edge of the lamp, there is a dusty thing that shows the paint. See look behind the vehicle with the vehicle in front, as if left and right symmetry; whether the old and new level of consistency on both sides of the tail lamp and the like. Look at the glass factory date. At the bottom of the glass, there is a “1....†that is the date of manufacture. This number “1†indicates the year, ie, 2001 or 2011, and if it is 2, it is 2002 or 2012. The black dot indicates the month, the black dot indicates the factory in the first half of the year, and the number of 7- black dots = the month (for example, " ...1 ", there are 4 black dots, and 7-4=3 , that is , the factory in March . ) Black spots are indicated after the figures in the second half of the year, with 13- black spots = month (for example " 1.... ", there are 4 black spots, 13-4 = 9 , that is September factory). Look at the screws on the door to see if there are any passive marks. Then look at the shape of the door frame, remove the rubber strip of the door frame, hold it at the top of the strip when it is removed, pull it down, and don't tear the strip. As shown in the above picture, when you open the tape, you will find a small dot. The dot is the reference material. It is smooth, orderly, and evenly spaced. The edge of the door frame is a few layers together. Often, the opposite occurs. Let's talk about the engine compartment. Look at the position of the front hood lock. Looking down from this lock position, you see the white crash beam (an example of a white car). It is white, and it is also white. of. In most cases, the color of the collision beam of the vehicle is the same as the color of the vehicle body. In a few cases, the aluminum alloy is not painted. If the colors are different, see if the screws in the tank frame have been screwed. Here again, the paint is painted on the screw. Usually the paint on the screws of the whole vehicle is the color, including the screws on the engine , including all the screws under the chassis . Inside the vehicle's fender, you can see there is no gilding repair inside. In fact, these conditions are still good, the arrow points to the lining of the leaves, this time the most important thing is to see whether the lining has folds, whether it has re-sprayed paint. Spray paint on the stringers only once or twice. Looking at the engine 's feet again, the age is too old, and it's normal for a family car to change his feet a few years. But if you are buying a new quasi- car , there are obvious signs of changing the machine. Even if there is no accident , the condition may not be very good. Sealant. The original sealant is soft in most cases and can be snagged in with a fingernail. Xiao Bian wants customers to polish your eyes when they buy a car.
Sack gabion is
cylindrical basket made of 8x10 double twisted steel woven wire mesh,
with mechanical characteristics higher than the ones suggested from EN
10223-3. It's filled with stones at the project site to form flexible
and permeable structures used for emergency and river training works
where local conditions require fast installation or where the water does
not allow for easy access to the site and where underwater installation
is necessary.
Sack Gabion Specification
Sack Gabion,Wire Mesh Sack Gabion,Coated Sack Gabion Box,Pvc Coating Sack Gabion ANPING KINDELONG WIRE MESH CO.,LTD. , https://www.apkdlwiremesh.com
Sack gabions are
supplied with steel reinforcing wires inserted during the manufacturing
process to facilitate closing during installation. The wire used for
the manufacture of gabion shall have a tensile strength between 3
80-550N/mm2 exceeding, in order to increase the tensile resistance of
the finished products, what is suggested from EN10223-3. Wire tolerances
are in accordance with EN 10218. Elongation shall not be less than 10%,
according to EN 10223-3. Test must be carried out on a sample at least
25 cm long. Meantime the adhesion of the zinc coating to the wire shall
be such that, when the wire is wrapped six turns around a mandrel having
four times the diameter of the wire, it does not flake or crack when
rubbing it with the bare fingers.