The Overhead Crane is designed for the whole lifting cranes, so as to ensure the whole smooth run of the lifting devices. The crane girders are of welded girder construction. This result in lower dead weights with a high degree of vertical and horizontal rigidity and smaller wheel loads being transmitted to the crane runway. End Carriage/End Truck,Crane end carriage,Crane End carriage Device Eurocrane (China) Co., Ltd. , https://www.cranes-group.com
Valve procurement specifications of the technical requirements
Valve procurement only clear specifications, categories, pressure on the procurement requirements to meet the traditional practices in the current market economy is not perfect environment. Because the valve manufacturer in order to compete for products, formed their own corporate standards and product personality. Therefore, valve buyers in the procurement of valves more detailed technical requirements, and valve manufacturers to achieve consensus, as a valve procurement contract annex is necessary. 1. General Requirements for Procurement Valves 1.1 The specifications and types of valves shall comply with the requirements of the pipe design documents. 1.2 valve model should indicate the number. If the enterprise standard, should indicate the relevant description of the model. 1.3 The working pressure of the valve, the required working pressure ≥ pipe, without affecting the price under the premise of the valve can withstand the working pressure should be greater than the actual working pressure of the pipeline; the valve closed condition on either side should be able to withstand 1.1 times the valve working pressure Value without leakage; the valve is open, the valve body should be able to withstand the pressure requirements of the work twice the valve. 1.4 Valve manufacturing standard number should be marked, if the corporate standards, procurement contracts should be accompanied by corporate documents. 2. Valve material 2.1 Body material, and indicate the valve body material grade and the actual physical and chemical testing data. 2.2 stem material, and strive to stainless steel stem (2CR13), large-diameter valve should also be stainless steel embedded valve stem. 2.3 nut material, the use of cast aluminum brass or cast aluminum bronze, and the hardness and strength are greater than the stem. 2.4 stem bushing material, the hardness and strength should not be greater than the stem, and in the water soaking conditions with the stem, the valve body does not form electrochemical corrosion. 2.5 sealing surface material ①different types of valves, sealing methods and material requirements vary; ② ordinary wedge gate valve, copper ring material, fixing methods, grinding methods should be described; ③ soft seal gate valve, valve lining rubber material Physical and chemical and health testing data; ④ butterfly valves should be marked on the sealing material on the valve body and sealing material on the disc; their physical and chemical testing data, especially the rubber hygiene requirements, anti-aging properties, wear resistance; Clear rubber and EPDM rubber, non-doped with recycled rubber. 2.6 Valve shaft packing ①Because the valve in the pipe network is usually not open and close frequently, it is required that the packing should not be activated within a few years and the packing should not be aged, and the sealing effect should be maintained for a long time. ② The valve shaft packing should withstand frequent opening and closing , The sealing effect of the good; ③ In view of the above requirements, the valve shaft filler for life or do not change for more than ten years; ④ filler to be replaced, the valve design should be considered under pressure to replace the measures. 3. Transmission Gearbox 3.1 Material and internal and external anti-corrosion requirements of the body and the same principle. 3.2 boxes should be sealed, the box assembly can withstand 3 meters of water column status soak. 3.3 Box opening and closing limit device, the adjustment nut should be in the box or set in the box, but need special tools to work. 3.4 Transmission structure design is reasonable, when opening and closing can only drive the valve shaft to rotate, do not make it move up and down, transmission components bite moderation, do not produce separation and sliding with load Hoist. 3.5 Variable speed transmission box and valve shaft seal can not be connected into a whole without leakage, otherwise there should be reliable anti-stringing measures. 3.6 box body without debris, the gear occlusion should have grease protection. 4. Valve actuator 4.1 Opening and closing the valve operation direction, should be closed clockwise. 4.2 Due to the valve in the pipe network, often manual opening and closing, opening and closing speed should not be too much, that is, large-diameter valves should also be within 200-600 turn. 4.3 In order to facilitate a person's opening and closing operation, under plumbing conditions, the maximum opening and closing torque should be 240N-m. 4.4 Valve opening and closing operation end should be square tenon, and size standardization, and facing the ground, so that people can directly operate from the ground. Valves with wheels are not suitable for underground pipe networks. 4.5 degree of opening and closing of the valve display ①valve opening and closing of the scale line should be cast in the gearbox cover or switch the direction of the display after the shell, all toward the ground, the scale brush on the phosphor to show eye-catching; ② indicating the material of the needle plate can be used in the case of better management of stainless steel plate, otherwise painted steel, do not use aluminum production; ③ indicator needle needle eye-catching, fixed firmly, once the opening and closing adjustment is accurate, should be rivets locking. 4.6 If the valve buried deeper, the operating mechanism and the display panel from the ground distance ≥ 1.5m, should be equipped with additional rod facilities, and fixed and stable, so that people from the ground to observe and operate That is, the network valve Closed operation, should not go down to work. 5. Valve performance test 5.1 When a valve is manufactured in a batch, an authoritative organization or a third-party inspection agency shall be entrusted to conduct the following performance tests: ①Opening and closing torques of the valve under working pressure; ② Under working pressure , To ensure that the valve closed tight open and close the number of times; ③ valve in the pipeline water flow resistance coefficient of the test. 5.2 The valve should be tested at the factory as follows: ①When the valve is in the open condition, the valve body shall withstand the internal pressure twice the pressure value of the valve; ② Under the closed condition of the valve, both sides shall withstand 1.1 times the valve working pressure , No leakage; but the metal seal butterfly valve, the leakage value is not greater than the relevant requirements. 6. Valve anti-corrosion treatment 6.1 The body (including variable speed transmission box) inside and outside, the first shot blasting sand rust, and strive to electrostatic spray powder non-toxic epoxy resin, the thickness of 0.3mm or more. Extra-large valve electrostatic spraying non-toxic epoxy resin difficulties, should also be brushing, spraying similar non-toxic epoxy paint. 6.2 All parts of the valve body and the valve plate require full corrosion protection. On the one hand, it will not be eroded in the water and will not cause electrochemical corrosion between the two metals. On the other hand, the smoothness of the surface reduces the resistance to over-water flow. 6.3 Anticorrosive epoxy resin or paint the body of the health requirements, there should be the corresponding authority of the test report. Chemical and physical properties should also meet the relevant requirements. 7. Valve packaging and transportation 7.1 Valve should be provided on both sides of the valve cover or light blocking plate seal. 7.2, small-caliber valves should be tied with straw, and transported by container mode is appropriate. 7.3 Large diameter valve also has simple wooden frame solid packaging, in order to avoid collision damage during transportation. 8. The valve manual and the factory to prove that the valve is a device, in the valve manual and the factory certificate should indicate the following relevant data: Valve Specifications; Model; Working pressure; Manufacturing standards; Body material; Stem material; Sealing material; Packing material; stem bushing material; inside and outside the anti-corrosion material; operation start direction; revolutions; under pressure conditions opening and closing torque; factory name; date of manufacture; factory number; weight; connecting flange aperture, the number of holes , The center hole distance; the overall length, width and height control dimensions are shown graphically; the valve flow resistance coefficient; the effective opening and closing times; the valve factory inspection of the relevant data and installation, maintenance precautions and so on.