1 Daily routine inspection and maintenance 1.1 Airtightness check of the whole machine Close the intake valve of the air respirator supply valve, open the bottle head valve, and then close the bottle head valve after 2 minutes. The pressure gauge drop value within 5 minutes after the bottle head valve is closed should not exceed 4 Mpa. If the pressure drop value within 5 minutes is greater than 4 Mpa, the air tightness of each component and connection should be checked separately. 1.2 Alarm pressure of the alarm Open the cylinder head valve and close the cylinder head valve when the pressure gauge indicates that the value rises above 7 Mpa. Observe that the pressure gauge drops to the start of the alarm. The initial pressure of the alarm should be between 4 Mpa and 6 Mpa. If the alarm start pressure exceeds this range The alarm should be removed to check whether all components are intact. If damaged, new components should be replaced. 1.3 Matching check of supply valve and full face mask Close the intake valve of the supply valve, after wearing a full face mask, open the bottle head valve, you will hear the sound of "sizzle" when inhaling; during exhalation and breath-holding, the air supply valve should stop supplying, no " The "sizzle" sound indicates that the supply valve and full face mask are well matched. If the gas supply valve is still supplying gas during exhalation and breath-holding, you can still hear the sound of "sizzle", indicating a mismatch. At this time, the supply valve and full face mask should be fully inspected or the supply valve and full face mask should be replaced, and the matching check should be repeated until it is qualified. 1 Routine maintenance 1.1 Air bottle and bottle head valve (1) Avoid collision, scratching and knocking of the air bottle, avoid high-temperature baking and high-cold freezing and exposure to sunlight, repair the paint off in time to prevent the bottle wall from rusting. (2) Air cylinders should be used according to the date marked on the cylinders. Regular inspections should be carried out. A hydraulic test inspection should be conducted every three years. (3) The air in the air bottle cannot be exhausted completely, and the residual pressure should not be less than 0.05Mpa. (4) When the bottle head valve is removed and repaired, and then the air bottle is reinstalled, it must pass the air tightness test of 28Mpa ~ 30Mpa, and can be used only after passing the test. 2.2 Pressure reducer Do not disassemble the pressure reducer at will during use. When the safety valve leaks, the chamber pressure of the pressure reducer and the safety valve should be re-examined. 2.3 Full face mask When the air breathing apparatus is not in use, the full face mask should be placed in the packing box, and it should not be under pressure during storage. It should be stored in a clean, dry warehouse, and should not be eroded by sun exposure and toxic gases and dust. 2.4 Supply valve Under normal circumstances, it is strictly prohibited to disassemble the supply valve. In case of fault repair, it should be installed as it is, and it can be used after passing the inspection. 2 Notes (1) Air respirator and its parts should avoid direct sunlight to avoid aging of rubber parts. (2) Air breathing apparatus is strictly prohibited from contact with grease. (3) A system for storage, maintenance and use of air respirator should be established. (4) The air cylinder cannot be filled with oxygen. (5) A comprehensive inspection of the air respirator should be conducted once a month. (6) Air respirators should not be used as diving respirators. (7) The pressure gauge should be calibrated once a year. (8) The compressed air used for breathing should be clean and meet the following requirements: Carbon monoxide does not exceed 5.5mg/m3 Carbon dioxide does not exceed 900 mg/m3 Oil does not exceed 0.5 mg/m3 Water does not exceed 50 mg/m3 Dongtai Hui Hong Kong Marine Equipment Co., Ltd. specializing in the production and sale: marine oil and water separator device, 15PPM type bilge water separator, SWCM type sewage treatment equipment, ZC sea life sewage treatment equipment, SWCH type marine sewage points Body storage cabinet, marine fuel separator, inflatable fire rescue air cushion, marine fuel supply unit, fuel separator unit , assembled pressure water tank, steam heating water tank, electric steam heating water tank, pressure water tank, electric heating Hot water cabinet, positive pressure fire-fighting air respirator, self-priming air respirator, electric air supply long-tube respirator, firefighter equipment, safety protection equipment, backpack-type wind extinguisher , portable wind extinguisher ; diving respirator Devices, wet and dry diving suits, emergency escape respirator devices, full-face gas masks, fire protection chemical suits, fully enclosed heavy chemical protection suits, firefighters fire protection suits, firefighters thermal insulation suits, fire monitors, breathing apparatus air pumps, Portable air foam gun device, international shore connection, copper fire spray dual water gun, copper interface, copper fire hydrant, pilot ladder, boarding ladder, motorized fire pump, submersible thermal insulation suit, new life jacket, old life jacket, inflatable life-saving clothes, fire enhanced dedicated life jacket, three marine life jackets, sportswear water, buoy, buoy lights, lamp life jackets, life rafts lamp, explosion proof lamp, portable riot searchlights, light explosion-proof flashlight, rechargeable Anti-riot flashlight, hydrostatic pressure releaser, self-supporting inflatable liferaft, ordinary throwing liferaft, hangable inflatable liferaft, factory liferaft , marine gong, marine fog clock, Robertson stretcher, Platform hanging cage . Column type hanging cage. Hanging basket. Fire-resistant lifeline, signal ball of various specifications, marine red light signal, marine parachute, floating smoke signal, combined smoke, rope thrower, rope throwing equipment, dry powder fire extinguisher, carbon dioxide fire extinguisher , Foam fire extinguisher, cart fire extinguisher, fire hose, fiberglass fire hose box, fire equipment box, fire extinguisher box, life jacket box and other products. The products are in compliance with the 2000 amendments to the 1974 "Convention on the Safety of Life at Sea" and the requirements of MSC.81(70) of the international life-saving equipment test, as well as the relevant requirements of the national standard, and obtained the type approval certificate of marine products from China Classification Society. Some of these products have been exported to Southeast Asia, Europe and the United States and other countries, and are well received by customers at home and abroad.
Product Description
Silica Anti Corrosive Pigment, with white
powder appearance, is mainly composed of calcium ion-exchanged amorphous silica
gel. This new-developed Nanotechnology, without toxic and heavy metal, matches
the environmental regulations. It can exchange calcium ions for the paint film
and hydrogen ions on the substrate, to neutralize the acidic substances, maintain
a high pH value, and prevent the substrate from erosive.
Meanwhile, the
calcium ions can be combined with the metal oxide film to form a protective
layer to protect the steel substrate, reduce corrosion, and prolong the service
life. Ion exchange anti-corrosive pigments do not contain heavy metals, toxic,
which provides a certain degree of rust protection.
Feature
1,Lower A/C
pigment addition levels vs. existing IES pigments
2, Lower interaction with catalysts
3, Low sensivity to prolonged
dispersion time.
Application Fields
Coil Coating,
Appliance Finishes, Transportation and Heavy-Duty, Equipment Coatings, Metal
Furniture Finishes.
Anti Corrosive Pigment, Silica Anticorrosion Pigment, Ion-exchanged Amorphous Silica Guangzhou Quanxu Technology Co Ltd , https://www.silicamattingagent.com