1. The maximum temperature resistance of the insulating material: 250° C
2. The highest service temperature: 200° C-250° C
3. Insulation resistance: ≥ 5 MΩÂ
4. Compressive strength: 1500V/5s
5. Power deviation rate: +5%
6. High voltage resistance: > 5KV
7. Maximum 1000mm× 8000mm, minimum 20mm× 20mm, thickness1.5mm (thinness 0.8mm, ----thickness 4mm)
Lead wire length: Standard 200mm, in case that the above dimensions are exceeded.
Spare Parts:Â
100K thermistor
3M Adhesive
Overheat Protection
Micro Thermostat
Digital Temperature Controller
Manual Temperature Controller
If you want to add the aboved spare parts, please advise.Â
Â
| Temperature Rating | 400 ° F ( 204 ° C ) maximum operating |
| Size/Shape Limitations | Maximum width of 48 inches , no maximum length |
| Thickness | ~0.06 inch(Single-Ply)~0.12 inch(Dual-Ply) |
| Voltage | Any AC or DC |
| Wattage | Customer specified(Normal maximum of 5 watts of 5 watts per square inch) |
| Power lead wire | Silicone rubber, SJ Power Cord, or Teflon insulated stranded wire |
| Attachment | Hooks, lacing eyelets, Or Velcro closure. Temperature control(Thermostat) |
| Â Â Description |
1. Silicon Rubber Heating Pad/Sheet has advantages of thinness, lightness, sticky and flexibility. 2. It can improve heat transfer, accelerate warming and decrease power under the process of operation. 3. They are heating fast and thermal conversion efficiency high. |
| Features: (1) Heating fast and long time using (2) Flexible and customization (3) Waterproof and non-toxic (Waterproof grad:IP68) Â Before purchasing, Please confirm the size first ( Iength*wide*thickness) Many thanks | |
 Technical Parameters:Â
1. The maximum temperature resistance of the insulating material: 250° C
2. The highest service temperature: 200° C-250° C
3. Insulation resistance: ≥ 5 MΩÂ
4. Compressive strength: 1500V/5s
5. Power deviation rate: +5%
6. High voltage resistance: > 5KV
7. Maximum 1000mm× 8000mm, minimum 20mm× 20mm, thickness1.5mm (thinness 0.8mm, ----thickness 4mm)
Lead wire length: Standard 200mm, in case that the above dimensions are exceeded.
Spare Parts:Â
100K thermistor
3M Adhesive
Overheat Protection
Micro Thermostat
Digital Temperature Controller
Manual Temperature Controller
If you want to add the aboved spare parts, please advise.Â
Â
| Temperature Rating | 400 ° F ( 204 ° C ) maximum operating |
| Size/Shape Limitations | Maximum width of 48 inches , no maximum length |
| Thickness | ~0.06 inch(Single-Ply)~0.12 inch(Dual-Ply) |
| Voltage | Any AC or DC |
| Wattage | Customer specified(Normal maximum of 5 watts of 5 watts per square inch) |
| Power lead wire | Silicone rubber, SJ Power Cord, or Teflon insulated stranded wire |
| Attachment | Hooks, lacing eyelets, Or Velcro closure. Temperature control(Thermostat) |
| Â Â Description |
1. Silicon Rubber Heating Pad/Sheet has advantages of thinness, lightness, sticky and flexibility. 2. It can improve heat transfer, accelerate warming and decrease power under the process of operation. 3. They are heating fast and thermal conversion efficiency high. |
| Features: (1) Heating fast and long time using (2) Flexible and customization (3) Waterproof and non-toxic (Waterproof grad:IP68) Â Before purchasing, Please confirm the size first ( Iength*wide*thickness) Many thanks | |
Â
Aluminum Coolers for Compressor, Aluminum plate&bar heat exchangers (oil cooler, Air Cooler /Charge Air Coolers,Compressor Coolers, Water Cooler and Combi Coolers ) have been widely applied for all kinds of compressor including air compressors, LNG-BOG recovery compressor, CNG compressor and more.
Heat Exchanger for Air Dryer, The heat exchangers transfer heat between a cold medium and the damp compressed air. This cools the compressed air to a pressure dew point. If required the condensation generated by the cooling process is collected in a condensation chamber integrated into the heat exchanger and continually drained off.
Advantage:
Compact, Lightweight, High Efficient Heat Transfer
Customize High Quality Aluminum plate-fin cooler upon your drawing, sample or parameter requirement.
FAQ
Q1:Could you customize oil cooler/heat exchanger?
We can manufacture plate-fin heat exchanger/oil cooler /intercooler according to your drawings or samples or parameter requirement.
Q2: I want to buy your products, how can I pay?
A :You can pay via T/T
Q3: How can you guarantee the quality?
A: One year's warranty against B/L date.
Q4: If we don`t find what we want on your website, what should we do?
A: You can email us the descriptions and pictures of the products you need, We will check whether we can make it.
Q5: Can we buy samples of each item for quality testing?
A: Yes, we understand quality test is important and we are glad to send the sample for quality testing.
Q6: What is the lead time?
A: Normal : Plate-fin heat exchanger for 2~3 weeks; Tube&fin or stacked layer coolers for 5 weeks. Exact time upon negotiation
Air Compressor Oil Cooler,CNG Compressor Aluminum Cooler,Compressor Gas Cooler and Radiator Assembly,Compressor Coolers,Charge Air Coolers
Wuxi Better Technology Co., Ltd , https://www.btheatexchanger.com